Riesenauswahl an Markenqualität. In-the- cut gibt es bei eBay! To cut a mirror, first use a sharpie and a straight edge to mark where you want it cut. Then, score the mirror by putting downward pressure on your wheel cutter as you trace the cut lines.

Measure correctly where you wish to cut. Take duct tape and stretch it between the measured areas. You place the tape firmly against the mirror. Step-by-Step: How to Cut a Mirror.

Here is a simple overview for customizing a mirror’s size: Clean the mirror. Place the mirror on a clean, flat surface. Score the mirror with a glass cutter. Snap the mirror according to the scored lines.

Make any sharp edges smooth. This video shows how to cut glass and mirrors with a manual hand-held glass cutter. This is extremely simple when using the proper tools. Anyone can do this!

GbojbBNitrile Work Gloves. See full list onhow. Jetzt neu oder gebraucht kaufen. Set a few sheets of newspaper down on a flat surface to protect your mirror.

Then, use your ruler and a permanent marker to draw a line where you want to cut the mirror. Squirt a few drops of glass cutting oil along the marked line. Pull the mirror so the half of the score line is off the edge of the surface you’re cutting on.

It should break cleanly right down the score line. You can use running pliers to pull and gently wiggle the “off cut”. For my first mirror project I painted a $thrift store lingerie bureau and replace the leaded glass with salvaged mirror. To cut the mirror, the supplies we used were a straight edge, tape to cover the straight edge, a measuring tape to measure, an over-sized mirror, a blanket to cover the table, cleaner to clean the mirror and the magic tool… the glass cutter.

Here is the inexpensive glass cutter we used which was purchased from Home Depot for $6. If the dowel is not centere you might break the mirror while pressing it down. Once the dowel is beneath the scored line, keep both of your hands on either side of the mirror on top of the dowel. Then, gently press down the mirror until you feel a snap in the mirror.

If the mirror doesn’t break, then try pressing down in different spots. After you’ve lubricated the line (or not), run the glass cutter along your line one good time, pressing down hard enough to hear an awful screeching sound. It will leave a scored line that looks like this: 4. Break the mirror down the scored line.

Draw your cut line with a washable glass marker, using a straight edge as a guide. Lay thick masking tape along the line to make it clear and to give a guiding ledge to your cutter, as it can be hard to distinguish the cut line from its reflection in the mirror.

Lubricate your glass cutter with oil. Since mirrors are basically glass with a reflective backing, you can cut them with a diamond-tipped wet saw blade. Step Stretch the tape measure across one side of the mirror. Place a dot at the appropriate measurement.

Position a ruler on the mirror where you want to make the cut. I have a huge mirror in my bathroom. Hold the ruler firmly in place with your weaker hand. How can I cut the mirror without taking it off from the wall?

I want to cut about 2-inches at the bottom so I can put some tiles in between the mirror and the counter top. Use consistent pressure that is just firm enough to make a thin visible scratch. Keep the wheel perpendicular to the glass. Keep in mind that you cannot start a cut in the middle of a mirror using this method.

Start at an edge of the glass and trace the shape of the template onto the mirror with a marker pen. Extend the cutting line to another edge of the mirror if necessary. You cut glass with a diamond tipped glass cutter. If it does not fracture the way you want you will replace the entire mirror.

Glue on the frame, glue on the tile. Slip the mirror edge into the dado, lining up one of its corners flush against the angled miter cut.

Then, holding the corner of the mirror in position, carefully mark where the opposite corner of. Set fire to the string next, and as soon as it’s all on fire, hold the glass and plunge it into the bucket of water. With the glass submerge take a firm stick and hit the glass below the point where you want to cut. Doing it in the water achieves two things: the blow will be softer and the water will lessen the vibrations.

There are many affordable types of functional and decorative mirrors that can reflect your personal style at home. If you need a mirror for your bathroom, hallway, bedroom, living room or dining room, you may need guidance when choosing the right size.

It’s beneficial to know where to buy mirror glass cut to size, and who to call for repairs, replacements and custom glass solutions. Specialising in Made to measure and cut to size mirrors, offering hour UK delivery.

Made to measure mirrors and glass in a wide range of mirror solutions including showers, splash backs, glass counters and mirrored walls.